User’s Manual of WGSW-2620HP 1 User’s Manual WGSW-2620HP 24-Port 10/100Mbps + 2 Gigabit TP/SFP Managed 802.3at PoE Switch
User’s Manual of WGSW-2620HP 10 Configuration. Additionally, the firmware includes advanced features such as IGMP snooping, QoS (Quality of Service),
User’s Manual of WGSW-2620HP 1004.8 Spanning Tree Protocol 4.8.1 Theory The Spanning Tree protocol can be used to detect and disable network loops,
User’s Manual of WGSW-2620HP 101 Bridge Protocol Data Units For STP to arrive at a stable network topology, the following information is used: The
User’s Manual of WGSW-2620HP Each port on a switch using STP exists is in one of the following five states: Blocking – the port is blocked from for
User’s Manual of WGSW-2620HP 4.8.2 Illustration of STP A simple illustration of three switches connected in a loop is depicted in the below diagram. I
User’s Manual of WGSW-2620HP Figure 4-8-3: After Applying the STA Rules 4.8.3 STP Parameters STP Operation Levels The Switch allows for two levels
User’s Manual of WGSW-2620HP Priority A relative priority for each switch – lower numbers give a higher priority and a greater chance of a given swit
User’s Manual of WGSW-2620HP Observe the following formulas when setting the above parameters: Max. Age _ 2 x (Forward Delay - 1 second) Max. Age _ 2
User’s Manual of WGSW-2620HP Max Age (6-40): The number of seconds a switch waits without receiving Spanning-tree Protocol configuration messages befo
User’s Manual of WGSW-2620HP 108 The page includes the following fields: Object Description • Priority The bridge identifier of the root bridge. It
User’s Manual of WGSW-2620HP 4.8.5 Port Configuration This web page provides the port configuration interface for STP. You can assign higher or lower
User’s Manual of WGSW-2620HP 111.3 How to Use This Manual This User Manual is structured as follows: Section 2, INSTALLATION The section explains the
User’s Manual of WGSW-2620HP Admin P2P: The rapid state transitions possible within STP are dependent upon whether the port concerned can only be conn
User’s Manual of WGSW-2620HP 111 4.9 DHCP Relay & Option 82 The Relay Agent Information option (Option82) is inserted by the DHCP relay agent when
User’s Manual of WGSW-2620HP Figure 4-9-1: DHCP Relay and Option 82 Function Interface Screenshot The page includes the following fields: Object
User’s Manual of WGSW-2620HP 4.10 LLDP Link Layer Discovery Protocol (LLDP) is used to discover basic information about neighboring devices on the loc
User’s Manual of WGSW-2620HP 4.10.2 Per Port Configuration This page allows the user to inspect and configure the current LLDP port settings, the web
User’s Manual of WGSW-2620HP 4.11 Access Control List The Access Control List (ACL) is a concept in computer security used to enforce privilege separa
User’s Manual of WGSW-2620HP 116 The page includes the following fields: IPv4 ACL Object Description Default VauleGroup ID 1 ~ 200 Action Per
User’s Manual of WGSW-2620HP 117 TCP Set this field if Packet Type is IPv4, else ignore. Any / FTP(21) / HTTP(80) Any Port Set this field if Packet Ty
User’s Manual of WGSW-2620HP 118 Binding Let device that has specific IP address and MAC address can use network. We can set specific IP address, M
User’s Manual of WGSW-2620HP 4.12 User Configuration This web page provide user configuration for switch management access level, the web screen in Fi
User’s Manual of WGSW-2620HP 12 1.4 Product Features ¾ Physical Port 24-Port 10/100Base-TX Fast Ethernet ports with IEEE 802.3af / IEEE 802.3at Po
User’s Manual of WGSW-2620HP 4.13 MAC Limit MAC limit allows users to set a maximum number of MAC addresses to be stored in the MAC address table. The
User’s Manual of WGSW-2620HP 4.13.2 MAC Limit Port Status This table displays current MAC Limit status of each port. Figure 4-13-2: MAC Limit – MAC L
User’s Manual of WGSW-2620HP 4.14 802.1X Configuration 802.1x is an IEEE authentication specification which prevents the client from accessing a wirel
User’s Manual of WGSW-2620HP Control Server version 3.0. RADIUS operates in a client/server model in which secure authentication information is exchan
User’s Manual of WGSW-2620HP Figure 4-14-2: EAP message exchange Ports in Authorized and Unauthorized States The switch port state determines whe
User’s Manual of WGSW-2620HP 4.14.2 System Configuration 802.1x makes use of the physical access characteristics of IEEE802 LAN infrastructures in ord
User’s Manual of WGSW-2620HP 126 The page includes the following fields: Object Description IEEE 802.1x Protocol: Enable or disable 802.1x protocol.
User’s Manual of WGSW-2620HP 4.14.3 802.1x Port Configuration In this page, you can select the specific port and configure the authorization state. Th
User’s Manual of WGSW-2620HP 4.14.4 Misc Configuration In this page, you can change the default configuration for the 802.1x standard: Figure 4-14-6:
User’s Manual of WGSW-2620HP 1294.15 QoS Configuration 4.15.1 Understand QoS Quality of Service (QoS) is an advanced traffic prioritization featur
User’s Manual of WGSW-2620HP 13 − Cisco ether-channel (Static Trunk) Spanning Tree Protocol - STP, IEEE 802.1D (Classic Spanning Tree Protocol) -
User’s Manual of WGSW-2620HP 4.15.2 QoS Configuration QoS settings allow customization of packet priority in order to facilitate delivery of data traf
User’s Manual of WGSW-2620HP The table includes the following fields: Object Description First Come First Service The sequence of packets sent is de
User’s Manual of WGSW-2620HP 4.15.2.2 QoS PerPort Configuration Configure the priority level for each port. With the drop-down selection item of Prior
User’s Manual of WGSW-2620HP 4.15.3 TOS/DSCP TOS/DSCP priority is obtained through a 6-bit Type-of-Service (TOS) or Differentiated Service Code Point
User’s Manual of WGSW-2620HP 4.15.3.1 TOS/DSCP Configuration The TOS/DSCP page provides fields for defining output queue to specific DSCP fields. When
User’s Manual of WGSW-2620HP 4.15.3.2 TOS/DSCP Port Configuration Set up IP TOS / DSCP mapping to 802.1p priority when receiving IPv4 packets, the Man
User’s Manual of WGSW-2620HP 4.16 Power over Ethernet Providing up to 24 PoE, in-line power interface, the WGSW-2620HP PoE Switch can easily build
User’s Manual of WGSW-2620HP 4.16.2 WGSW-2620HP Power Management In a power over Ethernet system, operating power is applied from a power source (PSU-
User’s Manual of WGSW-2620HP 138 The page includes the following fields: Object Description System PoE Admin Mode Allows user enable or disable PoE f
User’s Manual of WGSW-2620HP Priority Set port priority for the POE power management It works on the “Classification” power limit mode only, value
User’s Manual of WGSW-2620HP 14 1.5 Product Specification Product WGSW-2620HP 24-Port 10/100Mbps + 2 Gigabit TP / SFP Managed 802.3at PoE Switch Hard
User’s Manual of WGSW-2620HP PD Classifications A PD may be classified by the PSE based on the classification information provided by the PD. The i
User’s Manual of WGSW-2620HP 5. CONSOLE MANAGEMENT The Managed Switch is equipped with a RS-232 DB9 connector as default. And support telnet manageme
User’s Manual of WGSW-2620HP 1. For security reason, please change and memorize the new username and password after this first setup. Username Max
User’s Manual of WGSW-2620HP Configure IP address 1. On “Switch(config)# ” prompt, enter the following command and press <Enter>. As show in
User’s Manual of WGSW-2620HP 144 5.3 Commands Level The following table lists the CLI commands and description. Modes Access Method Prompt Exit Me
User’s Manual of WGSW-2620HP 145 6. COMMAND LINE INTERFACE 6.1 Operation Notice To enter the “configuration” mode, you need to be in the privileged
User’s Manual of WGSW-2620HP 146 6.1.2. Command Help You may enter ? at any command mode, and the CLI will return possible commands at that point, alo
User’s Manual of WGSW-2620HP 147 6.3 Switch Static Configuration 6.3.1 Port Configuration and show status port state Turn the port state on or off. S
User’s Manual of WGSW-2620HP 148 port rate Description: Set port effective ingress or egress rate. Syntax: port rate <ingress | egress> <0..8
User’s Manual of WGSW-2620HP 149 Port 2 Information ---------------------------------------------------------------------- State: on Link: down Tr
User’s Manual of WGSW-2620HP 15 Auto negotiation status, trunk status. Port Mirroring TX / RX / Both 1 to 1 monitor Bandwidth Control Ingress / Egress
User’s Manual of WGSW-2620HP 150 show port protection Description: Show protected port information. Switch(config)# show port protection --------+--
User’s Manual of WGSW-2620HP 6.4 Trunk Configuration Trunk allows the switch to combine ports so that they function like a single high-speed link. It
User’s Manual of WGSW-2620HP 152 no trunk Description: Delete an existing trunk group. Syntax: no trunk <trunk-id> Parameters: <trunk-id>
User’s Manual of WGSW-2620HP show lacp agg Description: Show LACP aggregator information. Syntax: show lacp agg <trunk-id> Parameters: <trunk
User’s Manual of WGSW-2620HP 154 6.5 VLAN Configuration 6.5.1 Virtual LANs A Virtual LAN (VLAN) is a logical network group that limits the broadcast
User’s Manual of WGSW-2620HP The Managed Switch support both Port-based VLAN and Tag-based (802.1Q) VLAN modes. The default configuration is tag-based
User’s Manual of WGSW-2620HP 6.5.3 Advanced 802.1Q VLAN Configuration Ingress filters configuration When a packet was received on a port, you can gove
User’s Manual of WGSW-2620HP 157 This VLAN entry has four members (from port1 to port4) and all members are untagged. no vlan Description: Delete VLAN
User’s Manual of WGSW-2620HP 158 show vlan pvid Description: Show port default VLAN id. Syntax: show vlan pvid [LIST] Parameters: [LIST] specifies th
User’s Manual of WGSW-2620HP 159 Switch(config)# show vlan filter Port | Rule 1 | Rule 2 Filter (nonmbr) (untag) -----------+------------+-----
User’s Manual of WGSW-2620HP 2. INSTALLATION This section describes the hardware features and installation of the Managed Switch on the desktop or ra
User’s Manual of WGSW-2620HP 160 Unicast/Multicast: Flood unicast/multicast filter Control Packets: Control packets filter IP multicast: IP m
User’s Manual of WGSW-2620HP 161 Parameters: The manager username and password is also used by the web UI. 6.7.2 IP Configuration User can configure
User’s Manual of WGSW-2620HP dhcp Description: Set switch as dhcp client, it can get ip from dhcp server. If you set this command, the switch will r
User’s Manual of WGSW-2620HP 163 6.7.6 Restore Configure File copy tftp <running-config | flash> Description: Retrieve configuration from the T
User’s Manual of WGSW-2620HP no mac-limit Description: Disable MAC limit. Mac-limit Description: Set port MAC limit value, 0 to turn off MAC limit of
User’s Manual of WGSW-2620HP 165 show mirror-port Description: Show port monitoring information
User’s Manual of WGSW-2620HP 166 6.10 Quality of Service There are four transmission queues with different priorities in the Managed Switch: Highest,
User’s Manual of WGSW-2620HP 167 [<highest-weight>][<sechighweight>][<sec low -weight>] [<lowest-weight>] e.g. qos priority we
User’s Manual of WGSW-2620HP 168 6.11 MAC Address Configuration clear mac-address-table Description: Clear all dynamic MAC address table entries. mac
User’s Manual of WGSW-2620HP 169 smac-address-table static Description: Set static unicast or multicast MAC address in secondary MAC address table. If
User’s Manual of WGSW-2620HP Reset button At the left of front panel, the reset button is designed for reboot the Managed Switch without turn off a
User’s Manual of WGSW-2620HP 6.12 STP/MSTP Commands [no] spanning-tree Description: Enable or disable spanning-tree. spanning-tree forward-delay Desc
User’s Manual of WGSW-2620HP The parameters must enforce the following relationships: 2*(hello-time + 1) <= maximum-age <= 2*(forward-delay - 1
User’s Manual of WGSW-2620HP 172 spanning-tree max-hops Description: Set spanning tree bridge maximum hops of CIST and all MSTIs. Syntax: spanning-tr
User’s Manual of WGSW-2620HP 173 Parameters: <0-240> specifies the port priority. The value must be in steps of 16. <port-list> specifies
User’s Manual of WGSW-2620HP 174 spanning-tree mst Description: Set spanning tree bridge priority of MSTI. Syntax: spanning-tree mst <0-15> pr
User’s Manual of WGSW-2620HP 175 no spanning-tree mst Description: Delete the specific MSTI. Syntax: no spanning-tree mst <0-15> Parameters: &l
User’s Manual of WGSW-2620HP 176 show spanning-tree mst <0-15> port <1-10> Parameters: <0-15> specifies the MSTI instance ID. <1-
User’s Manual of WGSW-2620HP 177 6.13 SNMP Any Network Management running the simple Network Management Protocol (SNMP) can be management the switch.
User’s Manual of WGSW-2620HP 178 e.g. snmp system-contact [email protected] show snmp system Description: Show SNMP system information. 6.13.2 Community
User’s Manual of WGSW-2620HP 179 Parameters: <ip-addr> specifies the IP address. <community-str> specifies the community string. <1..65
User’s Manual of WGSW-2620HP Per 10/100Mbps port, PoE interfaces (Port-1 to Por-24) LED Color Function Lights: To indicate the link through that
User’s Manual of WGSW-2620HP 180 igmp querier Description: Enable/disable IGMP snooping querier. Syntax: [no] igmp querier igmp CrossVLAN Desc
User’s Manual of WGSW-2620HP 181 6.15 802.1x Protocol dot1x Description: Enable or disable 802.1x. Syntax: [no] dot1x radius-server host Descript
User’s Manual of WGSW-2620HP 182 dot1x timeout quiet-period Description: Set 802.1x quiet period. (default: 60 seconds) Syntax: dot1x timeout quiet-p
User’s Manual of WGSW-2620HP 183 Parameters: <1..10> specifies the maximum request retries. dot1x timeout re-authperiod Description: Set 802.1x
User’s Manual of WGSW-2620HP 184 6.16 Access Control List Packets can be forwarded or dropped by ACL rules include Ipv4 or non-Ipv4. The Managed Switc
User’s Manual of WGSW-2620HP 185 Port ID : Any Hit Octet Count : 165074 Hit Packet count : 472 acl (add|edit) <1-220> (permit|deny) <0-4094&
User’s Manual of WGSW-2620HP 186 <0-FF> specifies the protocol value. <0-FF> specifies the protocol mask. <0-FFFF> specifies the sou
User’s Manual of WGSW-2620HP 187 6.17 Binding Let device that has specific IP address and MAC address can use network. We can set specific IP address,
User’s Manual of WGSW-2620HP 188 Parameters: <1-220> specifies the group id. A.B.C.D specifies the MAC address. <0-4094> specifies the VLA
User’s Manual of WGSW-2620HP 6.18 Power over Ethernet Commands show poe Show System Power over Ethernet information show poe status Show PoE port i
User’s Manual of WGSW-2620HP 2.1.3 Switch Rear Panel The rear panel of the Managed Switch indicates an AC inlet power socket, which accepts input powe
User’s Manual of WGSW-2620HP 190 show poe status Description: Show per PoE port information Command Level Global Configuration Syntax: show poe stat
User’s Manual of WGSW-2620HP 6.18.2 Configure PoE Over Temperature Protection poe temperature-protection enable Description: Configure PoE over tempe
User’s Manual of WGSW-2620HP 192 6.18.3 Configure PoE -- System poe limit-mode Description: Configure System PoE power limit mode information Command
User’s Manual of WGSW-2620HP 193Example: Switch(config)# poe limit-mode consumption Switch(config)# show poe Maximum Available Power POE Admin mode
User’s Manual of WGSW-2620HP 194poe admin-mode Description: Configure System PoE Admin mode information Command Level Global Configuration Syntax: p
User’s Manual of WGSW-2620HP 195 Switch (config)# poe admin-mode disable Switch(config)# show poe Maximum Available Power POE Admin mode Temperature
User’s Manual of WGSW-2620HP 196poe temperature Description: Configure System PoE Temperature Threshold information Command Level Global Configurati
User’s Manual of WGSW-2620HP 197poe usage Description: Configure System PoE Usage Threshold information Command Level Global Configuration Syntax: p
User’s Manual of WGSW-2620HP 198 6.18.4 Configure PoE -- Port poe enable Description: Enabling or disabling the port POE injects function. Command
User’s Manual of WGSW-2620HP 199poe priority Description: Set port priority for the power supply management. Command Level: Global Configuration
User’s Manual of WGSW-2620HP Trademarks Copyright © PLANET Technology Corp. 2011. Contents subject to which revision without prior notice. PLANET is a
User’s Manual of WGSW-2620HP 2.2 Install the Switch This section describes how to install the Managed Switch and make connections to it. Please read t
User’s Manual of WGSW-2620HP 200 poe power-mode Description: Set poe power mode for the power supply management Command Level Global Configuration
User’s Manual of WGSW-2620HP 201 7. SWITCH OPERATION 7.1 Address Table The Switch is implemented with an address table. This address table composed of
User’s Manual of WGSW-2620HP 202 7.5 Auto-Negotiation The STP ports on the Switch have built-in "Auto-negotiation". This technology automat
User’s Manual of WGSW-2620HP 8. POWER OVER ETHERNET OVERVIEW What is PoE? Based on the global standard IEEE 802.3af, PoE is a technology for wired Et
User’s Manual of WGSW-2620HP The data pairs are used. Since Ethernet pairs are transformer coupled at each end, it is possible to apply DC power to th
User’s Manual of WGSW-2620HP 205 The PoE Provision Process While adding PoE support to networked devices is relatively painless, it should be realized
User’s Manual of WGSW-2620HP 206 Start-up Once line detection and optional classification stages are completed, the PSE must switch from low voltage t
User’s Manual of WGSW-2620HP 207 9. TROUBLE SHOOTING This chapter contains information to help you solve problems. If the Ethernet Switch is not funct
User’s Manual of WGSW-2620HP While IP Address be changed or forgotten admin password – To reset the IP address to the default IP Address “192.168
User’s Manual of WGSW-2620HP Appendix A—RJ-45 Pin Assignment A.1 Switch's RJ-45 Pin Assignments 1000Mbps, 1000Base T Contact MDI MDI-X 1 BI_D
User’s Manual of WGSW-2620HP 2.2.2 Rack Mounting To install the Managed Switch in a 19-inch standard rack, please follows the instructions described b
User’s Manual of WGSW-2620HP The standard cable, RJ-45 pin assignment The standard RJ-45 receptacle/connector There are 8 wires on a standard UTP
EC Declaration of Conformity For the following equipment: *Type of Product: 24-Port 10/100Mbps + 2 Gigabit TP/ SFP Managed 802.3at PoE Switch
User’s Manual of WGSW-2620HP 2.2.3 Installing the SFP transceiver The sections describe how to insert an SFP transceiver into an SFP slot. The SFP tra
User’s Manual of WGSW-2620HP Before connect the other switches, workstation or Media Converter. 1. Make sure both side of the SFP transceiver are wit
User’s Manual of WGSW-2620HP 3. SWITCH MANAGEMENT This chapter explains the methods that you can use to configure management access to the Managed Sw
User’s Manual of WGSW-2620HP 25 3.2 Management Access Overview The Managed Switch gives you the flexibility to access and manage it using any or all o
User’s Manual of WGSW-2620HP 3.3 Web Management The Managed Switch offers management features that allow users to manage the Managed Switch from anywh
User’s Manual of WGSW-2620HP 3.4 SNMP-Based Network Management You can use an external SNMP-based application to configure and manage the Managed S
User’s Manual of WGSW-2620HP Direct Access Direct access to the administration console is achieved by directly connecting a terminal or a PC equippe
User’s Manual of WGSW-2620HP 3.6 Protocols The Managed Switch supports the following protocols: Virtual terminal protocols, such as Telnet Simpl
User’s Manual of WGSW-2620HP 3 TABLE OF CONTENTS 1. INTRODUCTION ...
User’s Manual of WGSW-2620HP 4. Web-Based Management This section introduces the configuration and functions of the Web-Based management. 4.1 About
User’s Manual of WGSW-2620HP 4.1.1 Requirements • The operate system of subscriber PC that running Windows XP/2003, Vista, Windows 7, MAC OS X , Linu
User’s Manual of WGSW-2620HP 1. After entering the username and password, the main screen appears as Figure 4-1-2. Figure 4-1-2: Web Main Page Scree
User’s Manual of WGSW-2620HP 4.1.3 Main WEB PAGE The Managed Switch provides a Web-based browser interface for configuring and managing it. This inter
User’s Manual of WGSW-2620HP Main Menu Using the onboard web agent, you can define system parameters, manage and control the Managed Switch, and all
User’s Manual of WGSW-2620HP 354.2 System Use the System menu items to display and configure basic administrative details of the Managed Switch. Unde
User’s Manual of WGSW-2620HP 4.2.1 System Information In System information, it has two parts of setting – Basic and Misc Config. We will describe the
User’s Manual of WGSW-2620HP 4.2.1.2 Misc Config Choose Misc Config from System Information of Managed Switch, the screen in Figure 4-2-2 appears. Fi
User’s Manual of WGSW-2620HP 38 threshold you set, broadcast storm control becomes active. The valid threshold values are 1/2, 1/4, 1/8, 1/16 and OF
User’s Manual of WGSW-2620HP 4.2.2 IP Configuration The Managed Switch is a network device which needs to be assigned an IP address for being identifi
User’s Manual of WGSW-2620HP 4 4.2.3 Console Port Info...
User’s Manual of WGSW-2620HP 40The page includes the following fields: Object Description DHCP Enable or disable the DHCP client function. When DH
User’s Manual of WGSW-2620HP 4.2.3 Console Port Info The Managed Switch provide local console interface for switch command line management, console po
User’s Manual of WGSW-2620HP 4.2.4 SNMP Configuration 4.2.4.1 SNMP Overview The Simple Network Management Protocol (SNMP) is an application layer pro
User’s Manual of WGSW-2620HP Management information base (MIB):A MIB is a collection of managed objects residing in a virtual information store. Co
User’s Manual of WGSW-2620HP • System Contact The textual identification of the contact person for this managed node, together with information on ho
User’s Manual of WGSW-2620HP 4.2.4.4 Trap Managers A trap manager is a management station that receives the trap messages generated by the switch. If
User’s Manual of WGSW-2620HP The page includes the following fields: Object Description Group Name: A string identifying the group name that this en
User’s Manual of WGSW-2620HP The page includes the following fields: Object Description View Name: A string identifying the view name that this entr
User’s Manual of WGSW-2620HP 48The page includes the following fields: Object Description Group Name: A string identifying the group name that this
User’s Manual of WGSW-2620HP 4.2.4.8 SNMP V3 usm-user Configure SNMPv3 users table on this page. The entry index keys are Engine ID and User Name. The
User’s Manual of WGSW-2620HP 5 4.8.2 Illustration of STP ...
User’s Manual of WGSW-2620HP 4.2.5 Syslong Setting The Syslog Setting page allows you to configure the logging of messages that are sent to remote sys
User’s Manual of WGSW-2620HP 4.2.6 System Log It provides the functions allowing the user to update the switch firmware via the Trivial File Transfer
User’s Manual of WGSW-2620HP 4.2.7 SNTP Setting It provides the functions allowing the user to update the switch firmware via the Trivial File Transfe
User’s Manual of WGSW-2620HP 4.2.8 Firmware Upgrade It provides the functions allowing the user to update the switch firmware via the Trivial File Tra
User’s Manual of WGSW-2620HP 4.2.8.2 HTTP Firmware Upgrade The HTTP Firmware Upgrade page contains fields for downloading system image files from the
User’s Manual of WGSW-2620HP 4. Select on the firmware then click “Upload”, the Software Upload Progress would show the file upload status. Firmwar
User’s Manual of WGSW-2620HP 4.2.9.2 TFTP Backup Configuration You can back up the current configuration from flash ROM to the TFTP server for the pur
User’s Manual of WGSW-2620HP 4.2.10 Factory Default Reset switch to default configuration. Click Default to reset all configurations to the default v
User’s Manual of WGSW-2620HP 4.3 Port Configuration Use the Port Configuration Menu to display or configure the Managed Switch's ports. This sect
User’s Manual of WGSW-2620HP Link: Indicate per port link up and link down status. Negotiation: Auto and Force. Being set as Auto, the speed and dupl
User’s Manual of WGSW-2620HP 6 6.4.2 LACP Command...
User’s Manual of WGSW-2620HP 4.3.2 Rate Control This page provides rate control on each port - it contains Ingress and Egress items and the unit is 12
User’s Manual of WGSW-2620HP 4.3.3 Port Status This page displays current port configurations and operating status - it is a ports’ configurations sum
User’s Manual of WGSW-2620HP 4.3.4 Port Statistics The following chart provides the current statistic information which displays the real-time packet
User’s Manual of WGSW-2620HP 4.3.5 Port Sniffer The Port Sniffer (mirroring) is a method for monitor traffic in switched networks. Traffic through a p
User’s Manual of WGSW-2620HP Figure 4-3-6: Port Sniffer Interface Screenshot The page includes the following fields: Object Description Sniffer Type
User’s Manual of WGSW-2620HP 4.3.6 Protect Port There are two protected port groups; ports in different groups can't communicate. In the same gro
User’s Manual of WGSW-2620HP 4.4 VLAN configuration 4.4.1 VLAN Overview A Virtual Local Area Network (VLAN) is a network topology configured accordi
User’s Manual of WGSW-2620HP VLAN can also provide a level of security to your network. IEEE 802.1Q VLAN will only deliver packets between stations th
User’s Manual of WGSW-2620HP Adding an IEEE802.1Q Tag 68 Dest. Addr. Src. Addr. Length/E. type Data Old CRC Dest. Addr. Src. Addr. E. type Ta
User’s Manual of WGSW-2620HP 4.4.2 Static VLAN Configuration A Virtual LAN (VLAN) is a logical network grouping that limits the broadcast domain. It
User’s Manual of WGSW-2620HP 7 6.18.4 Configure PoE -- Port ...
User’s Manual of WGSW-2620HP 4.4.3 Port-based VLAN Packets can go among only members of the same VLAN group. Note all unselected ports are treated as
User’s Manual of WGSW-2620HP By adding ports to the VLAN you have created one port-based VLAN group completely. Figure 4-4-3: Static VLAN Interface
User’s Manual of WGSW-2620HP 72 4.4.4 802.1Q VLAN Tagged-based VLAN is an IEEE 802.1Q specification standard. Therefore, it is possible to create a VL
User’s Manual of WGSW-2620HP 4.4.4.1 VLAN Group Configuration VLAN Group Configuration Figure 4-4-4: VLAN Group Configuration Interface Screensho
User’s Manual of WGSW-2620HP Figure 4-4-5: VLAN Group Configuration Interface Screenshot 5. Select specific port as member port and the screen in F
User’s Manual of WGSW-2620HP Figure 4-4-6: 802.1Q VLAN Setting Interface Screenshot The page includes the following fields: Object Description VLAN
User’s Manual of WGSW-2620HP 4.4.4.2 VLAN Filter 802.1Q VLAN Port Configuration This page is used for configuring the Switch port VLAN. The VLAN pe
User’s Manual of WGSW-2620HP 77 The VLAN ID must as same as the VLAN ID that the port belong to VLAN group, or the untagged traffic will be dropped. I
User’s Manual of WGSW-2620HP 4.4.5 GVRP VLAN GVRP (GARP VLAN Registration Protocol or Generic VLAN Registration Protocol) is a protocol that facilitat
User’s Manual of WGSW-2620HP 4.4.5.1 GVRP Setting To configure GVRP Enable global GVRP function: select GVRP enable "Enable". Enable port G
User’s Manual of WGSW-2620HP 8 1. Introduction The PLANET Layer 2 Managed Switch – WGSW-2620HP is 24-Port 10/100Mbps + 2 Gigabit TP/SFP Managed 802.
User’s Manual of WGSW-2620HP 4.4.5.2 GVRP Table The GVRP Table can be used to display dynamic VLANs from being learned via GVRP. Figure 4-4-9: GVR
User’s Manual of WGSW-2620HP 4.4.6 Q-in-Q VLAN IEEE 802.1Q Tunneling (Q-in-Q) IEEE 802.1Q Tunneling (QinQ) is designed for service providers carryi
User’s Manual of WGSW-2620HP The Managed Switch supports multiple VLAN tags and can therefore be used in MAN applications as a provider bridge, aggreg
User’s Manual of WGSW-2620HP 83 The page includes the following fields: Object Description Enable: Sets the Managed Switch to QinQ mode, and allow
User’s Manual of WGSW-2620HP 4.4.6.2 Q-in-Q Tunnel Setting Business customers of service providers often have specific requirements for VLAN IDs and t
User’s Manual of WGSW-2620HP 4.5 Trunking Port trunking is the combination of several ports or network cables to expand the connection speed beyond th
User’s Manual of WGSW-2620HP 4.5.1 Aggregator setting This section provides Port Trunk-Aggregator Setting of each port from the Managed Switch, the sc
User’s Manual of WGSW-2620HP Work ports: This column field allows the user to type in the total number of active port up to four. With LACP static tru
User’s Manual of WGSW-2620HP Figure 4-5-3: Static Trunking Group Information Screenshot The page includes the following fields: Object Description
User’s Manual of WGSW-2620HP Figure 4-5-4: Aggregation Information of Switch 1 Screenshot 5. Click on the tab of Aggregator Information to check th
User’s Manual of WGSW-2620HP 1.2 Product Description Power over Ethernet The PoE in-line power following the standard IEEE 802.3af and IEEE 802.3at ma
User’s Manual of WGSW-2620HP Figure 4-5-5: Switch 2 Configuration Interface Screenshot 10. Click on the tab of Aggregator Information to check the
User’s Manual of WGSW-2620HP 4.5.3 State Activity Having set up the LACP aggregator on the tab of Aggregator Setting, you can configure the state acti
User’s Manual of WGSW-2620HP 4.6 Forwarding and Filtering The frames of Ethernet Packets contain a MAC address (SMAC address), which shows the MAC add
User’s Manual of WGSW-2620HP 4.6.2 Static MAC Table You can add a static MAC address that remains in the switch's address table regardless of whe
User’s Manual of WGSW-2620HP 4.6.3 MAC Filtering By filtering MAC address, the switch can easily filter the pre-configured MAC address and reduce the
User’s Manual of WGSW-2620HP 4.7 IGMP Snooping 4.7.1 Theory The Internet Group Management Protocol (IGMP) lets host and routers share information abo
User’s Manual of WGSW-2620HP Figure 4-7-2: Multicast Flooding Figure 4-7-3: IGMP Snooping Multicast Stream Control 96
User’s Manual of WGSW-2620HP 97 IGMP Versions 1 and 2 Multicast groups allow members to join or leave at any time. IGMP provides the method for member
User’s Manual of WGSW-2620HP The states a computer will go through to join or to leave a multicast group are shown below: Figure 4-7-4: IGMP State T
User’s Manual of WGSW-2620HP 4.7.2 IGMP Configuration The Managed Switch support IP multicast, you can enable IGMP protocol on web management’s switch
Kommentare zu diesen Handbüchern